Home :: Shop By Manufacturer :: Simpson Strong-Tie Anchoring Systems :: Chemical Anchors :: Epoxy, Acrylic & Vinylester Chemical Anchors
Home :: Fasteners :: Chemical Anchors :: ET Epoxy-Tie

ET56 Simpson Strong-Tie - ET56 - ET 56 oz Epoxy-Tie Adhesive

SKU: ET56
List Price $88.51
Your Price $61.96
You Save $26.55
Qty
 


We Will Also Ship...
Internationally
APO/FPO
Epoxy-Tie ET is a two-component, 100% solids epoxy-based system for use as a high strength, non-shrink anchor grouting material. Resin and hardener are dispensed and mixed simultaneously through the mixing nozzle. ET meets the ASTM C-881 specifications for Type I II, IV and V Grade 3, Classes B and C.
  • UsesThreaded rod anchoring - Rebar dowelling - Bonding hardened concrete to hardened concrete - Pick proof sealant around doors, windows and fixtures - Paste-over for crack injection.
  • ApplicationSurfaces to receive epoxy must be clean. For installations in or through standing water, see Adhesive Anchors Application Guidelines for details. The base material temperature must be 40° F or above at the time of installation. For best results, material should be 70° F - 80° F at the time of application. Cartridges should not be immersed in water to facilitate warming. To warm cold material, the cartridges should be stored in a warm, uniformly heated area or storage container for a sufficient time to allow epoxy to warm completely. Mixed material in nozzle can harden in 5-7 minutes at a temperature of 40° F or above.
  • Shelf LifeTwo years from date of manufacture in unopened container.
  • Storage ConditionsFor best results store between 45° F - 90° F. To store partially used cartridges, leave hardened nozzle in place. To re-use, attach new nozzle.
  • ColorResin – white; Hardener – black; amine based. When properly mixed, ET adhesive will be a uniform medium gray color.
  • Clean UpUncured material — Wipe up with cotton cloths. If desired scrub area with abrasive, waterbased cleaner and flush with water. If approved, solvents such as ketones (MEK, acetone, etc.), laquer thinner, or adhesive remover can be used. DO NOT USE SOLVENTS TO CLEAN ADHESIVE FROM SKIN. Take appropriate precautions when handling flammable solvents. Solvents may damage surfaces to which they are applied. Cured Material: Chip or grind off surface.
  • Chemical ResistanceVery good to excellent against distilled water, inorganic acids and alkalis. Fair to good against organic acids and alkalis, and many organic solvents. Poor against Ketones. For more detailed information see Technical Bulletin T-SAS-CHEMRES04.
  • Suggested SpecificationsAnchoring Adhesive shall be a two-component 100% solids epoxy based system supplied in manufacturer's standard side-by-side cartridge and dispensed through a static-mixing nozzle supplied by the manufacturer. Epoxy shall meet the minimum requirements of ASTM C-881 specification for Type I, II, IV, and V, Grade 3, Class B and C and must develop a minimum 13,390 psi compressive yield strength after 7 day cure. Epoxy must have a heat deflection temperature of a minimum 168°F(76°C). Adhesive shall be Epoxy-Tie ET from Simpson Strong-Tie, Dublin, CA. Anchors shall be installed per Simpson Strong-Tie's instructions for Epoxy-Tie ET.
  • Test CriteriaAnchors installed with ET adhesive have been tested in accordance with ICBO's Acceptance Criteria for Adhesive Anchors in Concrete and Masonry Elements (AC58). Between Simpson Strong-Tie in-house testing and ICBO report ER-4945, ET adhesive is recognized for the following: Seismic and Wind Loading. Long Term Creep at Elevated Temperature. Static Loading at Elevated Temperature. Damp Holes. Freeze-Thaw Conditions. Critical and Minimum Edge Distance and Spacing. In addition, anchors installed with ET adhesive have been tested in accordance with ICBO's Acceptance Criteria for Unreinforced Masonry Anchors (AC60).
  • Chemical Anchor Shipping NotesChemical Anchors can only be shipped using a ground shipping method. Because of the chemicals involved in the chemical anchors these products cannont be shipped via any air method. To expidite shipping we will sometimes have the order shipped from one of the manufacturers warehouses around the country when ever possible.

Customer Reviews


Write A Review

Additional Product Accessories

Simpson Strong-Tie - EDT22B Manual Dispensing Tool for 22 oz. Cartridges EDT22A
Simpson Strong-Tie - EDT22B Manual Dispensing Tool for 22 oz. Cartridges
Manual Dispensing Tool for 22 oz. Cartridges
$59.88
EDT22AP Simpson Strong-Tie - Pneumatic Dispensing Tool for 22 oz. Cartridges EDT22AP
EDT22AP Simpson Strong-Tie - Pneumatic Dispensing Tool for 22 oz. Cartridges
The EDT22AP has an ergonomically designed nylon reinforced handle complete with power adjustment. This extremely lightweight tool (6 lbs.) also features a power piston return.
$577.80
EDT56AP Simpson Strong-Tie - Pneumatic Dispensing Tool for 56 oz. Cartridges EDT56AP
EDT56AP Simpson Strong-Tie - Pneumatic Dispensing Tool for 56 oz. Cartridges
The EDT56AP has an ergonomically designed nylon reinforced handle complete with power adjustment. This lightweight tool (9 lbs.) also features a power piston return.
$834.16
EMN50 Simpson Strong-Tie - High Volume Mixing Nozzel EMN50
EMN50 Simpson Strong-Tie - High Volume Mixing Nozzel
A Hi-Volume 5/8 in diameter 24 element nozzle, with an integrally molded retaining nut. This nozzle provides approximately 2 times the dispensing rate of the EMN37. The major outer diameter is 7/8 - - . Fits 22 and 56oz. side-by-side cartridges
$13.40


 
SSL